TM-F3 Air-Gas Burner Flame Treatment Prepress Machine
Basic Info
Model No.: TM-F3
Product Description
Model NO.: TM-F3 Height of Work Piece: 25-250 mm Conveyer Size: 230mm Conveyer Transfer Speed: 0-10m/Min Fuels for Flame Processor: Liquefied Petroleum Gas Machine Weight: 155 Kg Transport Package: Plywood Case or Wooden Case as Required Origin: China(Mainland) Lame Area: 25~250mm Bottle Mouth Diameter: 12-24mm Output: 1800~3000PCS/Hr Compress Air: 6 Bar Machine Dimension: 2200X1200X700 mm Trademark: Tamprinter Specification: CE HS Code: 8419399090 Air-Gas burner Flame Treatment Machine
Specifications:
Lame area25~250mm
Height of work piece25-250 mm
Bottle mouth diameter12-24mm
Conveyer size230mm
Output1800~3000Pcs/Hr
Conveyer transfer speed0-10m/min
Compress air6 bar
Fuels for flame processorliquefied petroleum gas
Power supplyAC 380V/ 50Hz, 3-Phase
Machine dimension2200X1200X700 mm (LXWXH)
Machine weight155 KG
Operational issues:
1 This machine uses 220V power supply, and combustible gases, and compressed by the compressor air ventilation when using the machine and away from danger highly flammable areas where conditions permit the best equipped with fire fighting equipment!
(2) The machine has a certain degree of risk, please pay attention to safety when using operator and the operator has certain associated processing consciousness!
Boot steps:
1 Plug 220V power supply, and pass on the combustible gas and compressed air, the air pressure is about 3-4KG around! Followed by seeing, hearing, smell and other methods to check whether there is leakage of the place, check Do not use open flame check, to avoid danger, you can use soapy water to check for leaks! Checked and then wipe to dry!
2 Open the emergency stop switch power to start the governor, confirmed a few weeks to let the whole operation and commissioning of the sharp turn running OK, and then press the combustible gas switch, and then try to turn on the combustible gas flame gun switch, ( just started not too wide ) then the ignition, allowing the flames to ignite, and then slowly open the air switch, and gas -switch synchronous adjustment, adjusted to the blue flames
On behalf of the flame has been adjusted, press workpiece speed and running speed, try to adjust the position of both sides of the flame, the flame come into contact with the surface, quickly through!
3 tables under a pressure regulator, a pressure regulator only on behalf of the combustible gas meter, and the other is an air pressure adjustment table, generally regulated at 3-4KG so on it!
4 Configure the emergency stop switch, under any circumstances, press the emergency stop switch, the machine will stop, but the machine is stopped, the combustible gas will shut down, but for safety reasons, turn off the gas main switch should be relatively synchronized properly!
5 When the work is shut down, turn off the combustible gas switch, first extinguish the flame, the flame gun surface is heat, please do not touch, so as not to burn, you can allow free air circulation for some time and then turn off the air! In order to achieve the cooling effect! From work and want to turn off the power switch, and combustible gas master switch for safety!
Packaging Detail: Plywood case
Delivery Detail: Within 7 days
The 2 spark flame treatment machine is use for pre-treatment PP, PET,
And PE bottle surface before printing.
Payment TermsTT/Western Union Contact us if you need more details on Flame Treatment Machine. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Treatment Prepress Machine、Treatment Flame Machine. If these products fail to match your need, please contact us and we would like to provide relevant information.
Flame area | 25~250mm |
Height of work piece | 25-250 mm |
Bottle mouth diameter | 12-24mm |
Conveyer size | 230mm |
Output | 1800~3000Pcs/Hr |
Conveyer transfer speed | 0-10m/min |
Compress air | 6 bar |
Fuels for flame processor | liquefied petroleum gas |
Power supply | AC 220V/ 50Hz, 1-Phase |
Specifications:
Lame area25~250mm
Height of work piece25-250 mm
Bottle mouth diameter12-24mm
Conveyer size230mm
Output1800~3000Pcs/Hr
Conveyer transfer speed0-10m/min
Compress air6 bar
Fuels for flame processorliquefied petroleum gas
Power supplyAC 380V/ 50Hz, 3-Phase
Machine dimension2200X1200X700 mm (LXWXH)
Machine weight155 KG
Operational issues:
1 This machine uses 220V power supply, and combustible gases, and compressed by the compressor air ventilation when using the machine and away from danger highly flammable areas where conditions permit the best equipped with fire fighting equipment!
(2) The machine has a certain degree of risk, please pay attention to safety when using operator and the operator has certain associated processing consciousness!
Boot steps:
1 Plug 220V power supply, and pass on the combustible gas and compressed air, the air pressure is about 3-4KG around! Followed by seeing, hearing, smell and other methods to check whether there is leakage of the place, check Do not use open flame check, to avoid danger, you can use soapy water to check for leaks! Checked and then wipe to dry!
2 Open the emergency stop switch power to start the governor, confirmed a few weeks to let the whole operation and commissioning of the sharp turn running OK, and then press the combustible gas switch, and then try to turn on the combustible gas flame gun switch, ( just started not too wide ) then the ignition, allowing the flames to ignite, and then slowly open the air switch, and gas -switch synchronous adjustment, adjusted to the blue flames
On behalf of the flame has been adjusted, press workpiece speed and running speed, try to adjust the position of both sides of the flame, the flame come into contact with the surface, quickly through!
3 tables under a pressure regulator, a pressure regulator only on behalf of the combustible gas meter, and the other is an air pressure adjustment table, generally regulated at 3-4KG so on it!
4 Configure the emergency stop switch, under any circumstances, press the emergency stop switch, the machine will stop, but the machine is stopped, the combustible gas will shut down, but for safety reasons, turn off the gas main switch should be relatively synchronized properly!
5 When the work is shut down, turn off the combustible gas switch, first extinguish the flame, the flame gun surface is heat, please do not touch, so as not to burn, you can allow free air circulation for some time and then turn off the air! In order to achieve the cooling effect! From work and want to turn off the power switch, and combustible gas master switch for safety!
Packaging Detail: Plywood case
Delivery Detail: Within 7 days
The 2 spark flame treatment machine is use for pre-treatment PP, PET,
And PE bottle surface before printing.
Payment TermsTT/Western Union Contact us if you need more details on Flame Treatment Machine. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Treatment Prepress Machine、Treatment Flame Machine. If these products fail to match your need, please contact us and we would like to provide relevant information.
Product Categories : Pre-Post Equipment > Other Pre-Post Equipment
Premium Related Products
Other Products
Hot Products
TM-AG900 High Quality Automatic Glitter Powder Coating MachineTam-F70A Air-Gas Burner Flame Treatment MachineTM-LED-150 Small Light Curing MachineTmg-1200h Automatic Screen Printing Squeegee Sharpener Squeegee Grinding MachineTM-IR1200m 300 Degree Celsius Dryer Glass Drying Machine Tunnel OvenTM-R6 2.14*2.14*1.15 M Cheap Manual Rotary 6-Color T-Shirt Screen Printing Machine with Flash DryerTM-C2-P High Quality Label Two Color Pad Printing MachineTM-S61 Ink Cup 6 Color Servo Pad Printer with ShuttleTM-F3 High Quality Cylinder Flame Treatment MachineUSB Mini Electric Pad Printer (TDY-300)High Speed One Color Tabletop Pad Printing Machine (TM-MINI)Tam-170-C Fabric Handbag Leather Embossing Manual A4 Hot Stamping MachinePneumatic Bottle Screen Printing Machine ManufacturerTM-R6 Manual 6-Color Texitile Screen Printer for T Shirt with SqueegeeTM-UV750 Ce UV Curing Machine for PlasticCe Automatic Large Format Oblique Arm Flat Screen Printing Machine